Use Linux and WebDAV to Facilitate Online Collaboration

Monday Mar 28th 2011 by Juliet Kemp

There are many options for online collaboration, but WebDAV remains a useful and straightforward way to share files. Software support at both the server and client ends sweetens the deal further.

The WebDAV protocol enables users to store and share files via HTTP. This is particularly valuable in cases where HTTP is usually read-only, as WebDAV allows writing as well. In addition to accessing documents, users can (with suitable permissions) edit and re-upload them. Think of it as a networked file-system run over http: or as a way of supporting long-distance collaboration on files. The protocol supports locking and versioning information, so once you've accessed the WebDAV folder, you can edit files without risking overwriting other people's edits. These days, there are more and more ways available to undertake online collaboration, but WebDAV remains a useful and straightforward way to share files, especially as it's supported by plenty of software at both server and client end.

Unlike FTP, HTTP provides strong authentication and encryption, as well as caching and proxy support -- and because WebDAV works over HTTP, WebDAV gets all of that for free. SSH would be another option, but SSH is a bit more limited in terms of moving files around, and it has nowhere near the quality of client support and tools available.

WebDAV and Apache2

It's straightforward to get an Apache server to serve up a WebDAV folder. The Apache module you want is mod_dav. To enable this on a Debian or Ubuntu system, just type:

a2enmod dav
a2enmod dav_fs
/etc/init.d/apache2 restart
mod_dav provides the server with the WebDAV functionality (i.e., it implements the relevant HTTP protocol extensions), and mod_dav_fs supports it, allowing access to resources in the server's filesystem. Additional detailed information on the dav and dav_fs modules is available on the Apache web page.

You'll also need to set up specific folders to access via WebDAV. Here's an example:

<Directory "/web/juliet/davfolder">
Dav On

Order Allow,Deny
Allow from all

AuthType Digest
AuthName WebDAV-Realm

AuthUserFile "/usr/var/webdav.passwd"

require user juliet

The most important line here is Dav On, which turns this directory into a WebDAV one. The rest is about securing access to the directory. It's important to make sure you have authentication set up before you enable WebDAV on any directories, or you'll have a big security hole. The config here uses MD5 Digest authentication (recommended over htaccess for security), and would limit all access to the named user. You could also use just require valid-user; or you can make your setup as complicated as MD5 Digest allows.

To allow writing to (as well as reading from) your directory, you'll need to change the permissions on that directory appropriately. In particular, the Apache user must be able to write to the directory. Again, note the security issues here! Hence, it's a good idea to keep your WebDAV directory reasonably separate from the rest of your website files.

To set WebDAV up manually, you'll need the following somewhere in your Apache conf file:

LoadModule dav_module /usr/lib/apache2/modules/
LoadModule dav_fs_module /usr/lib/apache2/modules/
Then restart Apache, and set up the directory you want to use as above.

Client-Side DAV

While DAV is usually provided via a web server, web browsers aren't a great way to access it -- at the most, you'll get a directory listing (if you've enabled that in your Apache setup) and read or download files, but not edit or upload them.

If you want graphical access, the Nautilus and Konqueror file-browsers both have built-in WebDAV support. Open the folder with dav:// (you'll be challenged for your username and password), and you should be able to move files back and forth from your local desktop, and edit them in place. If you have problems, check the file/directory permissions server-side.

Another possible client for WebDAV is cadaver, a command-line client that works rather like an FTP client. To make a connection, type:

You'll be challenged for a username and password, then given a command-line prompt in the specified folder. You can then use get filename and put filename (or mget and mput) to grab or to upload files. cadaver also allows you to edit the metadata on files, which Nautilus and Konqueror don't.

Another option is to use fusedav (available as a package for Debian or Ubuntu) to access WebDAV directories as part of your normal filesystem. You'll need to add your user to the fuse usergroup with adduser username fuse. Be sure to log out and in again so it takes effect. Then use:

fusedav localfolder
to open the remote directory and mount it as localfolder. Note that this directory must already exist. I had problems getting this to work, but other people seem to be using it fine.

More Fun With WebDAV

mod_dav_fs, as used above, provides a back end that allows you to use the server directory system to provide WebDAV files. There are also other back end providers available -- for example, you can use mod_dav_svn to serve a Subversion repository via Apache. If you do this, you'll need to load the mod_dav_lock module as well (mod_dav_fs doesn't need this locking module as it does its own locking). As WebDAV is an open protocol, there's also scope to do other things with it yourself if you have particular requirements. It's a useful technology to have in your stable of file-sharing options.

Juliet Kemp has been messing around with Linux systems, for financial reward and otherwise, for about a decade. She is also the author of "Linux System Administration Recipes: A Problem-Solution Approach" (Apress, 2009).

Follow ServerWatch on Twitter

Mobile Site | Full Site
Copyright 2017 © QuinStreet Inc. All Rights Reserved